BUICK LUCERNE
CHEVY IMPALA / MONTE CARLO 2006-2008
A
B
1
Disconnect the negative battery terminal
to prevent an accidental short
circuit.
1
Unclip and remove the trim panel
around radio and a/c control.
(Figure A)
2
Remove (6) 9/32” screws to extract
radio and a/c control from sub dash.
(Figure B)
3
Continue to kit assembly.
2
95-3305 DASH DISASSEMBLY
A
B
C
SILVERADO WITH SLT OPTION/SUBURBAN
CHEVY AVALANCHE/TAHOE
GMC YUKON/SIERRA WITH SLT OPTION 2007-08
Unclip and remove radio trim panel.
(Figure A)
2
Remove (2) 8mm screws securing
switch panel below climate controls.
Unplug and remove switch panel.
(Figure B)
3
Remove (2) 8mm screws securing climate
controls. Unplug and remove climate
controls. (Figure B)
4
Remove (4) 9/32” screws securing
radio. Unplug and remove the radio.
(Figure C)
5
Continue to kit assembly.
*Note: Refer also to the instructions included with the aftermarket radio.
Disconnect the negative battery terminal
to prevent an accidental short circuit.
1
3
95-3305 DASH DISASSEMBLY
CHEVY EXPRESS VAN 2008/GMC SAVANNA 2008
Remove (2)10mm bolts from below knee bolster under steering column and remove
panel.
2
3 Remove (2)10mm bolts from panel below passenger dash airbag and remove panel.
Unsnap and remove radio and instrument cluster panel. (May not be necessary to
completely remove radio and instrument cluster panel to access radio.)
4
5 Remove (4) 9/32” bolts to remove radio.
Continue to kit assembly.
*Note: Refer also to the instructions included with the aftermarket radio.
1 Disconnect the negative battery terminal to prevent an accidental short circuit.
4
95-3305 DASH DISASSEMBLY
A
B
C
AUX
BAND FWD REV SEEK SEEK
PASSENGER AIR BAG
AUX
D
12:02 103:5
E
SUZUKI XL-7 2007-08
Press in on sides of the shifter boot to
release it from the shifter trim panel.
(Figure A)
2
Lift the boot up to access the Allen
screw securing the shifter knob to the
shifter lever. Loosen the Allen screw
and remove the shifter knob.
(Figure B)
3
Remove (1) torx screw from the shifter
trim panel (Figure C), then using a
panel removal tool unsnap the shifter
trim panel. Unplug and remove the
panel. (Figure D)
4
Remove (4) 9/32” screws securing
the radio. Unplug and remove the
radio.
6
Using a panel removal tool unsnap
the radio trim panel. Unplug and
remove the panel. (Figure E)
5
Continue to kit assembly.
*Note: Refer also to the instructions included with the aftermarket radio.
Disconnect the negative battery terminal
to prevent an accidental short circuit.
1
95-3305 KIT ASSEMBLY
B
C
C
DOUBLE DIN RADIO PROVISION
STACKED ISO UNITS PROVISION
Slide the DDIN radio unit into the trim
plate bracket assembly and secure the
unit to the kit using the screws supplied
with the head unit. (Figure C)
2
Continue to final assembly.
*Note: Refer also to the instructions included with the aftermarket radio.
Slide the appropriate bracket into the
trim plate aligning the holes in the
trim plate to the clips on the bracket.
(Figure B)
1
Slide the stacked ISO DIN units into the
trim plate bracket assembly and
secure the units to the kit using the
screws supplied with the head units.
(Figure C)
2
Slide the appropriate bracket into the
trim plate aligning the holes in the
trim plate to the clips on the bracket.
(Figure B)
1
NOTE: XL-7 ONLY
Trim top corners of radio housing.
(Figure A)
B
A
NOTE: XL-7 ONLY
Trim top corners of radio housing.
(Figure A)
A
5
95-3305 FINAL ASSEMBLY
FINAL ASSEMBLY
(A) Strip wire ends back 1/2"
B) Twist ends together
C) Solder
D) Tape
A
B
C
D
Locate the factory wiring harness in the dash. Metra recommends using the
proper mating adapter and making connections as shown. (Isolate and individually
tape off the ends of any unused wires to prevent electrical short circuit.)
Re-connect the negative battery terminal and test the unit for proper operation.
Reassemble radio and dash assemblies in reverse order of disassembly.
1
2
3
6
FINAL WIRING CONNECTIONS
Make wiring connections using the EIA color code chart shown below and the instructions included with the
head unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and
individually tape off ends of any unused wires to prevent electrical short circuit.
METRA / EIA WIRING CODE
12V Ignition / Acc. . . . . . . . . . Red
12V Batt / Memory. . . . . . . . . Yellow
Ground. . . . . . . . . . . . . . . . . . Black*
Power Antenna. . . . . . . . . . . . Blue
Amp Turn-On . . . . . . . . . . . . . Blue / White
Amp Ground. . . . . . . . . . . . . . Black / White
Illumination . . . . . . . . . . . . . . Orange
Dimmer . . . . . . . . . . . . . . . . . Orange / White
Right Front (+) . . . . . . . . . . . . Gray
Right Front (-). . . . . . . . . . . . . Gray/ Black
Left Front (+) . . . . . . . . . . . . . White
Left Front (-). . . . . . . . . . . . . . White / Black
Right Rear (+) . . . . . . . . . . . . Violet
Right Rear (-) . . . . . . . . . . . . . Violet / Black
Left Rear (+) . . . . . . . . . . . . . Green
Left Rear (-) . . . . . . . . . . . . . . Green / Black
*NOTE: When a Black wire is not present, ground radio to vehicle chassis.
All colors may not be present on all leads due to manufacturer’s specifications.
source: http://content.abt.com/documents/180...05_install.pdf
CHEVY IMPALA / MONTE CARLO 2006-2008
A
B
1
Disconnect the negative battery terminal
to prevent an accidental short
circuit.
1
Unclip and remove the trim panel
around radio and a/c control.
(Figure A)
2
Remove (6) 9/32” screws to extract
radio and a/c control from sub dash.
(Figure B)
3
Continue to kit assembly.
2
95-3305 DASH DISASSEMBLY
A
B
C
SILVERADO WITH SLT OPTION/SUBURBAN
CHEVY AVALANCHE/TAHOE
GMC YUKON/SIERRA WITH SLT OPTION 2007-08
Unclip and remove radio trim panel.
(Figure A)
2
Remove (2) 8mm screws securing
switch panel below climate controls.
Unplug and remove switch panel.
(Figure B)
3
Remove (2) 8mm screws securing climate
controls. Unplug and remove climate
controls. (Figure B)
4
Remove (4) 9/32” screws securing
radio. Unplug and remove the radio.
(Figure C)
5
Continue to kit assembly.
*Note: Refer also to the instructions included with the aftermarket radio.
Disconnect the negative battery terminal
to prevent an accidental short circuit.
1
3
95-3305 DASH DISASSEMBLY
CHEVY EXPRESS VAN 2008/GMC SAVANNA 2008
Remove (2)10mm bolts from below knee bolster under steering column and remove
panel.
2
3 Remove (2)10mm bolts from panel below passenger dash airbag and remove panel.
Unsnap and remove radio and instrument cluster panel. (May not be necessary to
completely remove radio and instrument cluster panel to access radio.)
4
5 Remove (4) 9/32” bolts to remove radio.
Continue to kit assembly.
*Note: Refer also to the instructions included with the aftermarket radio.
1 Disconnect the negative battery terminal to prevent an accidental short circuit.
4
95-3305 DASH DISASSEMBLY
A
B
C
AUX
BAND FWD REV SEEK SEEK
PASSENGER AIR BAG
AUX
D
12:02 103:5
E
SUZUKI XL-7 2007-08
Press in on sides of the shifter boot to
release it from the shifter trim panel.
(Figure A)
2
Lift the boot up to access the Allen
screw securing the shifter knob to the
shifter lever. Loosen the Allen screw
and remove the shifter knob.
(Figure B)
3
Remove (1) torx screw from the shifter
trim panel (Figure C), then using a
panel removal tool unsnap the shifter
trim panel. Unplug and remove the
panel. (Figure D)
4
Remove (4) 9/32” screws securing
the radio. Unplug and remove the
radio.
6
Using a panel removal tool unsnap
the radio trim panel. Unplug and
remove the panel. (Figure E)
5
Continue to kit assembly.
*Note: Refer also to the instructions included with the aftermarket radio.
Disconnect the negative battery terminal
to prevent an accidental short circuit.
1
95-3305 KIT ASSEMBLY
B
C
C
DOUBLE DIN RADIO PROVISION
STACKED ISO UNITS PROVISION
Slide the DDIN radio unit into the trim
plate bracket assembly and secure the
unit to the kit using the screws supplied
with the head unit. (Figure C)
2
Continue to final assembly.
*Note: Refer also to the instructions included with the aftermarket radio.
Slide the appropriate bracket into the
trim plate aligning the holes in the
trim plate to the clips on the bracket.
(Figure B)
1
Slide the stacked ISO DIN units into the
trim plate bracket assembly and
secure the units to the kit using the
screws supplied with the head units.
(Figure C)
2
Slide the appropriate bracket into the
trim plate aligning the holes in the
trim plate to the clips on the bracket.
(Figure B)
1
NOTE: XL-7 ONLY
Trim top corners of radio housing.
(Figure A)
B
A
NOTE: XL-7 ONLY
Trim top corners of radio housing.
(Figure A)
A
5
95-3305 FINAL ASSEMBLY
FINAL ASSEMBLY
(A) Strip wire ends back 1/2"
B) Twist ends together
C) Solder
D) Tape
A
B
C
D
Locate the factory wiring harness in the dash. Metra recommends using the
proper mating adapter and making connections as shown. (Isolate and individually
tape off the ends of any unused wires to prevent electrical short circuit.)
Re-connect the negative battery terminal and test the unit for proper operation.
Reassemble radio and dash assemblies in reverse order of disassembly.
1
2
3
6
FINAL WIRING CONNECTIONS
Make wiring connections using the EIA color code chart shown below and the instructions included with the
head unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and
individually tape off ends of any unused wires to prevent electrical short circuit.
METRA / EIA WIRING CODE
12V Ignition / Acc. . . . . . . . . . Red
12V Batt / Memory. . . . . . . . . Yellow
Ground. . . . . . . . . . . . . . . . . . Black*
Power Antenna. . . . . . . . . . . . Blue
Amp Turn-On . . . . . . . . . . . . . Blue / White
Amp Ground. . . . . . . . . . . . . . Black / White
Illumination . . . . . . . . . . . . . . Orange
Dimmer . . . . . . . . . . . . . . . . . Orange / White
Right Front (+) . . . . . . . . . . . . Gray
Right Front (-). . . . . . . . . . . . . Gray/ Black
Left Front (+) . . . . . . . . . . . . . White
Left Front (-). . . . . . . . . . . . . . White / Black
Right Rear (+) . . . . . . . . . . . . Violet
Right Rear (-) . . . . . . . . . . . . . Violet / Black
Left Rear (+) . . . . . . . . . . . . . Green
Left Rear (-) . . . . . . . . . . . . . . Green / Black
*NOTE: When a Black wire is not present, ground radio to vehicle chassis.
All colors may not be present on all leads due to manufacturer’s specifications.
source: http://content.abt.com/documents/180...05_install.pdf
0 komentar:
Posting Komentar